Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH Collision Detection

DTC B1788 Rear Occupant Classification Sensor RH Collision Detection

DESCRIPTION

DTC B1788 is output when the occupant classification ECU receives a collision detection signal sent by the rear occupant classification sensor RH if an accident occurs.

DTC B1788 is also output when the front seat assembly RH is subjected to a strong impact, even if an actual accident does not occur.

However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1788 can be cleared by "Zero point calibration" and "Sensitivity check".

Therefore, if DTC B1788 is output, first perform "Zero point calibration" and "Sensitivity check".

DTC No.

DTC Detection Condition

Trouble Area

B1788

  • Front seat assembly RH malfunction
  • Occupant classification ECU malfunction
  • Rear occupant classification sensor RH detected a large load
  • Front seat assembly RH (Rear occupant classification sensor RH)
  • Occupant classification ECU

INSPECTION PROCEDURE

1 PERFORM ZERO POINT CALIBRATION

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to the ON position.
  3.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed

2 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

3 CHECK DTC

  1. Turn the ignition switch to the ON position.
  2. Clear the DTCs stored in the memory HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  3.  Turn the ignition switch to the LOCK position.
  4.  Turn the ignition switch to the ON position.
  5.  Check the DTCs (35).

OK: DTC B1788 is not output. HINT: Codes other than DTC B1788 may be output at this time, but they are not related to this check.

4 REPLACE FRONT SEAT ASSEMBLY RH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the front seat assembly RH ( for flat type, SE-48 for manual seat, SE-58 for power seat).

HINT: Perform the inspection using parts from a normal vehicle if possible.

5 PERFORM ZERO POINT CALIBRATION

  1. Connect the negative (-) terminal cable to the battery.
  2.  Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed.

6 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

7 CHECK DTC

  1. Turn the ignition switch to the ON position.
  2.  Clear the DTCs stored in the memory.

    HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  3.  Turn the ignition switch to the LOCK position.
  4.  Turn the ignition switch to the ON position.
  5.  Check the DTCs (35).

OK: DTC B1788 is not output. HINT: Codes other than DTC B1788 may be output at this time, but they are not related to this check.

8 REPLACE OCCUPANT CLASSIFICATION ECU

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the occupant classification ECU

9 PERFORM ZERO POINT CALIBRATION

  1. Connect the negative (-) terminal cable to the batter.
  2.  Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed.

10 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Zero point calibration" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

END

Other materials:

Lumbar support adjuster assembly
INSPECTION 1.

Related news

  • Nissan Rogue Service Manual: The low washer fluid warning continues displaying, ordoes not display
  • Hyundai Elantra: Battery saver function
  • Kia Soul: Cylinder Block Inspection
  • Daytime running light system
  • Buick LaCrosse: Care of the CDDVD Player

  • Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Rear Occupant Classification Sensor RH CollisionDetection