Toyota Sienna Service Manual: Open in Side Squib LH Circuit

Toyota Sienna Service Manual: Open in Side Squib LH Circuit

DTC B0116/48 Open in Side Squib LH Circuit

DESCRIPTION

The side squib LH circuit consists of the center airbag sensor assembly and the front seat side assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0116/48 is recorded when an open circuit is detected in the side squib LH circuit.

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

  •  Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester.
  •  After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front seat side airbag assembly LH.
  4.  Connect the black wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the front seat side airbag assembly LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory.
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs

OK: DTC B0116/48 is not output.

HINT: Codes other than DTC B0116/48 may be output at this time, but they are not related to this check.

REPLACE FRONT SEAT ASSEMBLY LH

2 CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

CHECK FLOOR WIRE

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4. Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory.
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs.

OK: DTC B0116/48 is not output.

HINT: Codes other than code B0116/48 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

Short in Side Squib LH Circuit
DTC B0115/47 Short in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH. This circuit instruc ...
Other materials:

Back-up Power Source Circuit
DESCRIPTION This is the back-up power source for the A/C amplifier. Power is supplied even when the ignition switch is off and is used for diagnostic trouble code memory, etc. WIRING DIAGRAM INSPECTION PROCEDURE 1 INSPECT FUSE (ECU-B) (a) Remove the ECU-B fuse from the engine room juncti ...

Grocery bag hooks
The hooks are designed to hang things like a grocery bag. Type A (front seatback) (if equipped) Type B (third seatback) Type C (luggage compartment) Type D (luggage compartment) Pull the hook up. WARNING Type C: When not in use, keep the grocery ...

Stereo component amplifier
COMPONENTS Removal 1. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY 2. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY  Disconnect the connectors.  Remove the 2 nuts and the stereo component amplifier assembly. Installation 1.

Related news

  • Nissan Rogue Service Manual: P0717 input speed sensor A
  • Toyota Sienna Service Manual: Hood
  • Toyota Corolla Repair Manual: Wiring
  • Hyundai Sonata: Carry emergency equipment
  • Toyota Sienna Service Manual: Removal

  • Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit

    Toyota Sienna Service Manual: Open in Side Squib LH Circuit