Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

Replacement

Hint

: components:

1. Remove front wheel

2. Disconnect front stabilizer link assy lh (lh (a/t) position)

3. Disconnect front stabilizer link assy rh (lh (a/t) position)

Hint

: remove the rh side by the same procedures as the lh side.

4. Separate front suspension arm sub–assy lower no.1 Lh

  1. Remove the bolt and 2 nuts, and separate the front suspension arm sub–assy lower no.1 Lh from the lower ball joint assy front lh.

5. Separate front suspension arm sub–assy lower no.1 Rh (lh (a/t) position)

Hint

: remove the rh side by the same procedures as the lh side.

6. Separate rack & pinion power steering gear assy (lh (a/t) position)

  1.  remove the 4 bolts, separate the rack & pinion power steering gear assy.

    Notice

    : loosen the bolt since the nut cannot be rotated.

  2.  suspend the rack & pinion power steering gear assy.

7. Suspend engine assy (lh (a/t) position)

8. Separate front suspension crossmember sub–assy (lh (a/t) position)

  1. Remove the 3 bolts and 3 nuts, disconnect the transverse engine engine mounting insulator and engine mounting member sub–assy center from the front suspension crossmember sub–assy.

  1. Remove the 4 bolts.
  2. lower the transmission jack, remove the front suspension crossmember sub–assy.

9. Remove front suspension arm sub–assy lower no.1 Lh

  1. Remove the 2 bolts, nut and front suspension arm sub– assy lower no.1 Lh from the front suspension crossmember sub–assy.

10. Temporary tighten front suspension arm sub–assy lower no.1 Lh

  1. Install the front suspension arm sub–assy lower no. 1 Lh, temporarily tighten the 2 bolts and nut.

11. Install front suspension crossmember sub–assy (lh (a/t) position)

  1.  lift the front suspension crossmember sub–assy up with a transmission jack.

  1. Insert sst to the base hole of the rh side crossmember and rh side of the vehicle.

    Sst 09670–00010

  2.  tighten the bolt temporarily in the order a and b.

  1. Insert sst to the base hole of the lh side of crossmember and lh side of the vehicle.

    Sst 09670–00010

  2.  tighten the bolt temporarily in the order a and b.
  3.  insert sst to the base hole of the rh side of crossmember and rh side of the vehicle.

    Sst 09670–00010

  1. Then tighten the bolt a and b by the specified torque.

    Torque:
    bolt a: 157 nvm (1,601 Kgf·cm, 116 ft·lbf) bolt b: 113 nvm (1,152 Kgf·cm, 83 ft·lbf)

  2.  insert sst to the base hole of the lh side of crossmember and lh side of the vehicle.

    Sst 09670–00010

  3.  tighten the bolt a and b by the specified torque.

    Torque:
    bolt a: 157 nvm (1,601 Kgf·cm, 116 ft·lbf) bolt b: 113 nvm (1,152 Kgf·cm, 83 ft·lbf)

  1. Connect the transverse engine engine mounting insulator and engine mounting member sub–assy center to the front suspension crossmember sub–assy.
  2.  install the 3 bolts and 3 nuts.

    Torque: 52 nvm (530 Kgf·cm, 38 ft·lbf)

12. Install rack & pinion power steering gear assy (lh (a/t) position)

  1.  install the rack & pinion power steering gear assy with the 4 bolts.

    Torque: 58 nvm (591 Kgf·cm, 43 ft·lbf)

13. Install front suspension arm sub–assy lower no.1 Lh

  1. Install the front suspension arm sub–assy lower no.1 Lh with the 2 nuts and bolt to the lower ball joint assy front lh.

    Torque: 89 nvm (908 Kgf·cm, 66 ft·lbf)

14. Install front suspension arm sub–assy lower no.1 Rh (lh (a/t) position)

Hint

: install the rh side by the same procedures as the lh side.

15. Install front stabilizer link assy lh (lh (a/t) position)

16. Install front stabilizer link assy rh (lh (a/t) position)

Hint

: install the rh side by the same procedure as the lh side.

17. Stabilize suspension

  1.  install the front wheel and jack down the vehicle.

    Torque: 103 nvm (1,050 Kgf·cm, 76 ft·lbf)

  2.  bounce the vehicle up and down several times to stabilize the suspension.

18. Fully tighten front suspension arm sub–assy lower no.1 Lh

  1. Fully tighten the 2 bolts and nut.

    Torque: 137 nvm (1,397 Kgf·cm, 101 ft·lbf)

Notice

: tighten the bolt since the nut cannot be rotated.

19. Inspect and adjust front wheel alignment

Disposal
1. Dispose shock absorber assy front lh  fully extend the shock absorber piston rod.  using a drill, make a hole in the cylinder as shown in the illustration to discharge the gas ...
Other materials:

Gauges and meters (multi-information display)
The displayed content may differ depending on the type of meter. 1 Tachometer Displays the engine speed in revolutions per minute. 2 Speedometer 3 Fuel gauge 4 Multi-information display The multi-information display presents the driver with a variety of drivingrelated data including the cu ...

Ecm/pcm processor
Dtc p0606 ecm/pcm processor Monitor description The ecm continuously monitors its internal circuits. This self–check insures that the ecm is functioning properly. If a malfunction is detected, the ecm will set the appropriate dtc and illuminate the mil. The two cpus, main and sub cpu ins ...

Replacement
1. Remove combination meter assembly 2. Disconnect brake master cylinder push rod clevis  remove the clip and push rod clevis pin and wave washer, and disconnect the push rod clevis from the brake pedal. 3.

Related news

  • Chevrolet Sonic Repair Manual: Fuel Tank Fuel Pump Module Replacement (Steel Tank)
  • Toyota Corolla Repair Manual: Engine rear oil seal
  • Hyundai Elantra: Checking tire inflation pressure
  • Buick LaCrosse: Variable Effort Steering
  • Kia Forte: Piston and Connecting Rod Reassembly

  • Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh

    Toyota Corolla Repair Manual: Front suspension arm sub–assy lower no.1 Lh