Mazda 3 Service Manual: Brake Pedal RemovalInstallation

Mazda 3 Service Manual: Brake Pedal Removal/Installation

CAUTION:

  • The clearance between the brake switch and the brake pedal is automatically adjusted to the correct amount when the brake switch is inserted into the installation hole on the brake pedal and rotated to fix in place. If the brake switch is not properly installed, the clearance may be incorrect, causing a brake light malfunction. Therefore, always verify that the brake pedal is properly installed and fully released before installing the brake switch to the pedal.

  • Once the brake switch clearance has automatically been adjusted, it cannot be adjusted again. Therefore, replace the switch with a new one when replacing the power brake unit or the pedal, or performing any procedure that changes the pedal stroke.

  • Secure the steering wheel using tape or a cable to prevent the steering shaft from rotating after disconnecting the steering shaft. If the steering wheel rotates after the steering shaft and the steering gear and linkage are disconnected, the internal parts of the clock spring could be damaged.

1. Remove the battery and battery tray..

2. Disconnect the vacuum hose from the insulator bracket as shown in the figure. (MZR 2.3 DISI Turbo)


3. Remove the wiring harness from the air duct. (MZR 2.3 DISI Turbo)


4. Remove the side wall (driver side)..

5. Disconnect the steering shaft from the steering gear and linkage..

6. Remove the accelerator pedal..

7. Remove in the order indicated in the table.

8. Install in the reverse order of removal.


1

Brake switch connector, wiring harness

2

Brake switch

(See Brake Switch Installation Note.)

3

Joint pin

(See Joint Pin Installation Note.)

4

Brake pedal

(See Brake Pedal Removal Note.)

5

Pedal pad


Brake Pedal Removal Note

1. Remove the brake pedal installation bolt and nuts.

2. Move the power brake unit to the vehicle front where the power brake unit fork does not interfere with the brake pedal arm.

3. Remove the brake pedal.

Joint Pin Installation Note

1. Install the new joint pin by aligning the pin holes of the brake pedal and power brake unit fork.

2. Verify that the joint pin touches the power brake unit fork completely.


Brake Switch Installation Note

1. Inspect the brake pedal..

2. With the brake pedal fully released, insert a new brake switch into the installation hole on the brake pedal.

3. Secure the brake switch by turning it counterclockwise45°

.


Related news

  • Toyota Sienna 2010-2018 Owners Manual: When stopping the engine with the shift lever in a position otherthan P
  • Toyota Camry: Regulations on the use of tire chains
  • Mercedes-Benz E-Class: Cleaning the display
  • Toyota Sienna Service Manual: Starter
  • Ford Fusion: Climate control

  • Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation

    Mazda 3 Service Manual: Brake Pedal RemovalInstallation